SLRSpeedBook online
Somebody picks up.
Orlando and 15 miles around.
← All articles

Common Contractor Problems Orlando Homeowners Face

October 27, 2026 · Guides · 9 min read

Contractor Problems in Orlando Start With the Climate

Orlando is not a forgiving place to do sloppy work. The metro sits at roughly 82 feet above sea level in central Florida, which means no coastal breeze to moderate the heat, afternoon thunderstorms from June through October that dump two to four inches of rain in under an hour, and a relative humidity that averages above 70 percent for most of the year. Any shortcut a contractor takes — a flashing that isn't fully sealed, a soffit vent that isn't screened, a caulk joint that isn't primed — fails faster here than it would in Atlanta or Charlotte. That's the baseline problem Orlando homeowners are working with.

We see the downstream effects of this constantly. A job that looked fine at punch-list becomes a water intrusion problem eighteen months later because the contractor used the wrong sealant for Florida's UV index. A roof replacement that passed inspection develops lifted shingles after the first major storm because the fastener pattern didn't meet the wind-uplift requirements for this wind zone. Understanding why these failures happen in Orlando specifically — rather than just what went wrong — is the first step toward catching them early.

The Housing Age Problem

A significant portion of Orlando's residential housing stock was built between the 1960s and the mid-1990s, before Florida adopted the statewide Florida Building Code in 2002. Homes in that age range were built to local county standards that varied widely and, in many cases, did not account for the wind-load requirements or moisture-barrier standards that are now mandatory.

When a contractor works on one of these older homes, they're often working with original materials that weren't designed to interface cleanly with modern products. Mixing old and new is where a lot of Orlando contractor problems begin. A common example: adding spray-foam insulation to an older attic that was designed to breathe. The foam seals the attic so tightly that condensation has nowhere to go, and within a season or two you have a mold problem that wasn't there before the contractor showed up.

Other age-related failure points we see regularly:

  • Galvanized plumbing in pre-1980s homes that a contractor patches with copper fittings, creating a galvanic corrosion point that fails within a few years.
  • Aluminum wiring in homes from the 1960s–70s that gets tied into modern copper circuits without the correct connectors — a fire risk that a bad electrical contractor can introduce and a home inspection won't always catch.
  • Flat or low-slope roofs on mid-century ranch homes that were re-roofed with materials rated for steeper pitches, which then pond water and fail prematurely.

If your home was built before 2002 and you're hiring for any structural, roofing, or mechanical work, ask the contractor explicitly how they're handling the transition between original and new materials. A contractor who doesn't have a clear answer is a contractor who hasn't thought it through.

The Five Most Common Contractor Problems We See in Orlando

1. Moisture Intrusion and Improper Flashing

This is the number-one failure mode in Central Florida. Orlando's summer rain comes fast, comes sideways in a storm, and comes often. Flashing — the metal or membrane material that seals roof-to-wall transitions, window frames, and penetrations — has to be installed correctly to handle that kind of water load. When it isn't, water finds its way into wall cavities and sits there in the warm, humid air until mold takes hold.

What to watch for inside your home: Staining at the top corners of windows, bubbling or soft drywall near exterior walls, a musty smell in rooms that face the prevailing wind (usually southwest in summer), or efflorescence — white chalky deposits — on interior masonry walls.

2. Roofing Shortcuts That Don't Meet Wind-Uplift Standards

Orlando sits in Wind Zone II under Florida Building Code, which requires specific fastener patterns, underlayment types, and shingle ratings for new roof installations. After major storms, demand for roofers spikes and out-of-state crews come in who may not be familiar with Florida's specific requirements. We've seen roofs installed with standard 3-tab shingles in areas that require architectural-grade, and fastener patterns that use four nails per shingle where six are required.

What to watch for: After the first significant storm following a new roof installation, walk the perimeter of your home and look for lifted tab edges, exposed underlayment at the ridge, or granule loss concentrated in one area (which suggests uneven fastening). Also check the attic for daylight visible through the decking — it shouldn't be there.

3. HVAC Work That Ignores Orlando's Humidity Load

Orlando's cooling season runs roughly nine months. An HVAC system that's sized incorrectly — almost always oversized, because contractors assume bigger is better — will short-cycle. It cools the air temperature quickly but doesn't run long enough to remove humidity. The result is a home that reads 74°F on the thermostat but feels clammy, and interior surfaces that stay damp enough to support mold growth.

What to watch for: Condensation on interior window glass during summer, a musty smell from supply vents, or visible moisture on the air handler cabinet. If your system was recently replaced and the new unit is a larger tonnage than the old one, ask to see the Manual J load calculation that justified the size increase.

4. Concrete and Stucco Cracks Left Unsealed

Orlando's sandy soil expands and contracts with the wet and dry seasons. Homes on slab foundations see minor seasonal movement that creates hairline cracks in stucco and concrete block exteriors. These are normal. What's not normal is a contractor who patches them with standard exterior caulk and paints over them without addressing the underlying movement or using a flexible elastomeric sealant rated for Florida's UV exposure.

What to watch for: Cracks that reappear in the same location within one season of being patched, caulk that has yellowed and pulled away from the crack edges, or paint that's bubbling along a repaired crack line. These are signs the repair wasn't done to last.

5. Unlicensed Work After Storms

After every major storm that affects the Orlando metro — and we get named storms and tropical systems regularly between June and November — unlicensed contractors flood the market. They offer fast starts, low prices, and no permits. The permit is the thing that matters most: it triggers an inspection, and the inspection is the only independent check on the quality of the work.

What to watch for: Any contractor who suggests skipping the permit to save money or speed up the job is a contractor who knows the work won't pass inspection. Verify every contractor's license at myfloridalicense.com before signing a contract. An active license with no disciplinary history takes thirty seconds to confirm.

Orlando's Two Annual Inspection Windows

The seasonal rhythm of Central Florida gives homeowners two natural points each year to assess their property for contractor-related problems:

Late May (pre-hurricane season): Before the summer storm pattern establishes, walk your roof line from the ground with binoculars, check all exterior caulk and flashing, clear gutters and downspouts, and inspect the attic for signs of moisture from the previous winter's rain events. This is also the window to complete any exterior work before afternoon storms make scheduling unreliable.

Late November (post-hurricane season): After the storm season closes, inspect for any damage that may have been minor enough to miss during the season but will worsen over the dry winter. Check for lifted flashing, cracked stucco, and any soft spots in the roof decking you can feel from inside the attic.

Building these two walkthroughs into your annual routine means contractor problems get caught at the defect stage rather than the damage stage.

What Homeowners Can Check Themselves

You don't need to be a contractor to spot the early signs of a problem. Here's what to look for after any significant project:

  • Attic inspection: Bring a flashlight and look for daylight, staining on the decking, or insulation that's been disturbed and not replaced evenly. Do this within sixty days of any roofing or insulation work.
  • Window and door frames: Press gently on the drywall return around every window and exterior door. Soft or spongy material means moisture has been sitting there.
  • Grout and caulk in wet areas: Any bathroom or kitchen work should have caulk joints that are fully filled, not cracked, and not pulling away from the tile. Grout should be sealed. Check these at thirty days and ninety days post-installation.
  • Electrical panel: After any electrical work, look for breakers that trip without explanation or outlets that don't hold a plug firmly. These aren't cosmetic — get them looked at.
  • Exterior paint and sealant: Florida's UV index is among the highest in the country. Paint that's chalking or peeling within two years of application was either the wrong product for the substrate or wasn't primed correctly.

None of these checks require tools or expertise. They require thirty minutes and knowing what you're looking for.

The Permit and Inspection Layer

Every significant trade project in Orlando — roofing, electrical, plumbing, HVAC, structural — requires a permit from Orange County, Osceola County, or whichever jurisdiction the property sits in. The permit process exists specifically to catch contractor problems before they become your problem. When a contractor pulls a permit, an inspector from the county comes out at defined stages of the work and signs off that it meets code.

When no permit is pulled, that check doesn't happen. You're relying entirely on the contractor's honesty and competence, with no independent verification. In a market like Orlando — where demand is high, licensed contractors are busy, and storm events bring in out-of-state crews — that's a significant risk.

If you're buying a home and the seller discloses recent work, ask to see the permits and inspection sign-offs. Work done without permits can become your liability at resale, and in some cases Orange County requires the work to be opened up and re-inspected at the new owner's expense.

The permit isn't a formality — it's the only independent check on whether the work was done right.

We work in this market every day. The problems above aren't hypothetical — they're the calls we get after another contractor's work has failed. Knowing what to watch for, when to inspect, and how to verify a contractor's credentials before the job starts is the most effective protection an Orlando homeowner has.

More from the blog

Book a time

Pick a day and a time. A person confirms it with you.

Loading open times…
Nothing is charged to book.
Built with